Pittsburgh Paints & Stains ULTRA Advanced Stain & Sealant in One is a premium quality wood stain with a penetrating acrylic oil formulation. High quality ULTRA Advanced wood stain will safeguard and enhance the natural beauty of exterior wood surfaces in the harshest conditions with advanced 2-way waterproofing and ultra UV protection. ULTRA Advanced stain has the benefits of Weatherflex® Application Technology.
ULTRA Advanced stain also comes with a satisfaction guarantee.
- Wood Stain and Sealant in One
- Advanced Two-Way Waterproofing Protection
- Ultra UV Premium Protection Guards Against Sun Damage
- The Stain can be Applied Even on Damp Wood Allowing You to Clean & Stain Your Deck in One Day
- After Staining, Wooden Surface Will be Rain Ready in Just 8 Hours
- Low Temperature Application Down to 35°F
- Able to be applied even on hot sunny days
Surface must be clean and free of all dust, dirt, mildew, oil, loose wood fibers and other contaminants. Use an exterior wood cleaner to prepare new wood prior to coating, and to clean and restore weathered, dirty surfaces and remove mildew stains. After rinsing, ensure surface is free of standing water. Remove grade stamps or pencil marks by sanding.
WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH-approved respirator and prevent skin contact to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the USEPA National Lead Information Hotline at 1-800-424‑LEAD or log on to www.epa.gov/lead. Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation.
Surface should be dry or damp to the touch - but not visibly wet. Remove any standing water. Avoid staining in direct sunlight or on hot surfaces. DO NOT THIN. Stir thoroughly and often during use. Apply to a small area and allow to dry to ensure acceptable appearance and penetration. Intermix containers to ensure color uniformity. Apply one thin coat with a high quality brush, roller, paint/stain pad or by spray equipment. When rolling or spraying, always back-brush for best results. To help avoid lap marks, apply to only a few boards at a time, and maintain a wet edge.
Apply when no precipitation is expected for 24 hours, and when air and surface temperatures are 35°F to 90°F (2°C to 32°C) and will remain above 35°F (2°C) for the next 24 hours.
Normally dries in 24 hours when applied in temperatures of 50°F (10°C) to 85°F (29°C). High humidity or low temperature application may prolong drying time.
Approximately 250 to 350 sq. ft. (23.2 to 32.5 sq. meters) per gallon (3.78 Liters) depending on application, wood texture and porosity.
Clean brushes and tools with warm, soapy water.
|41-2601||Semi-Transparent||Neutral/Ultradeep/Accent/Clear||Quart/946 mL (04), 1/2 Pint/236 mL (16), Gallon/3.78 L (01), 5 Gallons/18.9 L (05)|
|41-2602||Semi-Transparent||Ready Mix Custom Color||5 Gallons/18.9 L (05), 1/2 Pint/236 mL (16), Gallon/3.78 L (01)|
|41-2603||Semi-Transparent||Ready Mix Custom Color||Gallon/3.78 L (01)|
|41-2604||Semi-Transparent||Ready Mix Custom Color||Gallon/3.78 L (01)|
|41-2605||Semi-Transparent||Ready Mix Custom Color||Gallon/3.78 L (01)|